output shaft replace 86 k100 ( motor out of bike)

yankeeone · 1 output shaft replace 86 k100 ( motor out of bike) Wed Jul 04, 2012 5:06 pm

yankeeone

Platinum member

Number of posts : 298

Hi I am doing another output shaft replace, this time with the motor out, I dont want to take off the air box, does any one have a way to place the motor on the bench up side down, blocks, stand ect. ?

Thanks

Rick G · 2 Re: output shaft replace 86 k100 ( motor out of bike) Wed Jul 04, 2012 6:13 pm

Rick G

admin

Number of posts : 12058

I have used an engine stand like for a car engine, it makes life easy

yankeeone

yankeeone

Platinum member

Number of posts : 298

Hi Rick, I cant figure out were to bolt a stand to on the motor, the two front mounting bolts seem strong , but wouldn't work well when the motor is upside down.

Thanks

Inge K.

Inge K.

VIP

Number of posts : 4321

Bolt a piece of plywood to the rear end, a 2"x2" leg down from each frame mounting.
A piece of 2"x2" between each leg and the plywood, and between the legs.

output shaft replace 86 k100 ( motor out of bike) Stativ10

output shaft replace 86 k100 ( motor out of bike) Stativ10

RT · 5 output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 9:18 am

RT

Life time member

Number of posts : 1925

Hey Inge how do you attach the stand to the ceiling?
RT

Inge K. · 6 Re: output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 9:22 am

Inge K.

VIP

Number of posts : 4321

Bolts through from the neighbour upstairs.

Rick G · 7 Re: output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 9:37 am

Rick G

admin

Number of posts : 12058

I had to make a few pieces but bolted it to the main block piece only with some clearance.

yankeeone · 8 Re: output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 8:39 pm

yankeeone

Platinum member

Number of posts : 298

Thanks for the suggestions. I think I will go with the plywood 2x2 rig, my engine stand has a 90hp outboard on it at the moment.

Brian

Inge K.

Inge K.

VIP

Number of posts : 4321

Hey Yankeeone, I think you still remember this one,
but..........as a reminder........some good info.

yankeeone

yankeeone

Platinum member

Number of posts : 298

Thanks for the input, I used the plywood and small boards to build the stand, all and all it is much more relaxed to change over the output shaft with the motor out, and upside down.

Sponsored content

1 output shaft replace 86 k100 ( motor out of bike) Wed Jul 04, 2012 5:06 pm

yankeeone

2 Re: output shaft replace 86 k100 ( motor out of bike) Wed Jul 04, 2012 6:13 pm

Rick G

3 Re: output shaft replace 86 k100 ( motor out of bike) Wed Jul 04, 2012 10:32 pm

yankeeone

4 Re: output shaft replace 86 k100 ( motor out of bike) Wed Jul 04, 2012 11:28 pm

Inge K.

5 output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 9:18 am

RT

6 Re: output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 9:22 am

Inge K.

7 Re: output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 9:37 am

Rick G

8 Re: output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 8:39 pm

yankeeone

9 Re: output shaft replace 86 k100 ( motor out of bike) Thu Jul 05, 2012 10:08 pm

Inge K.

10 Re: output shaft replace 86 k100 ( motor out of bike) Mon Jul 09, 2012 10:27 pm

yankeeone

11 Re: output shaft replace 86 k100 ( motor out of bike)

Sponsored content