BMW K bikes (Bricks)


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


1Back to top Go down   K100 Oil Filter Change Empty K100 Oil Filter Change Sun Apr 05, 2009 4:48 pm

Mike

avatar
New member
New member
I've read the "stuck oil filter" correspondence from May last year, and would just like to ask a couple of questions in addition. Does anyone have any other methods of routinely removing a K100 filter and installing the new one without the BMW tool? I can't get one here (Cape Town) at the moment, and anyway it's an expensive item here, it seems. (Which is likely, as that is true for anything that's Beemer.) The screwdriver penetration option does seem a bit vicious, although my concern is rather how one gets the right tightness on the replacement filter, given that you don't have the appropriate tool.

"Crazy Frog", if you're out there: do I understand correctly that you suggest filling the filter with oil prior to installation? The handbook gives two engine oil capacities at oil change, one when the filter is replaced and one when it isn't, the difference obviously being the filter capacity. Is there any particular reason why you suggest not just oiling the seal but filling the filter? If one does so, then when replacing the oil you would use the lower capacity recommendation, I imagine.

Cheers, All. Thanks for the Forum.

    

2Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Sun Apr 05, 2009 10:31 pm

Crazy Frog

Crazy Frog
admin
admin
Hey Mike

The reason that I fill up the filter is that I don't like to have my oil pump running dry (even for few seconds). The other reason is that when the filter is pre-filled, when filling up the engine you just have to look at the site glass. Usually, If I fill it up to 3/4 of the site glass I don't have to add any oil after. I never rely on the book for oil quantity. The site glass is what count.

A filter wrench is cheap here in Cdn. I may be able to send you one. Just contact me by Email.

Cheers

Bert

    

3Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Fri Apr 29, 2016 12:12 pm

Danish biker

Danish biker
Platinum member
Platinum member
Old post but not many suggestions how to get the oil filter off and the new one tightened enough with out a special tool.

Any one?

    

4Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Fri Apr 29, 2016 12:17 pm

Corkboy

Corkboy
Life time member
Life time member
I don't think there is any easy way to do it without the tool, except removing the whole oilpan and using the age old method of punching it with a screwdriver.

Get the tool - it's pretty cheap and makes the job a whole lot easier.


__________________________________________________
Regards,

Corkboy '87 K100RS SE (The black one - one of the two bikes I'm sorry I sold)
             '87 K100RS 0140995 (Gone)
             '97 K1100LT 0188024 (Gone)
             '08 K1200GT Wedge - but still a K
             '08 Transalp 700
    

5Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Fri Apr 29, 2016 12:32 pm

Danish biker

Danish biker
Platinum member
Platinum member
Corkboy wrote:I don't think there is any easy way to do it without the tool, except removing the whole oilpan and using the age old method of punching it with a screwdriver.

Get the tool - it's pretty cheap and makes the job a whole lot easier.

I was lucky that the local bike shop will lent me one tomorrow, how ever this link could be usefull to others:

https://youtu.be/L9t6cUCwXRg

    

6Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Fri Apr 29, 2016 3:58 pm

92KK 84WW Olaf

avatar
Life time member
Life time member
There is no problem in doing it without the tool. You just remove the bottom cover AFTER draining the oil. Slightly messy but not a problem. Refitting the bottom cover uses a sealant instead of a gasket. Once its off you can access the messy oil covered filter.

Fitting new filter is easier as its only done up hand tight. Put the new filter in before replacing the bottom cover. You can in theory take off the circular cover and put the filter back through the hole after replacing the bottom cover but you won't have finger room to tighten the filter even to hand tight, that's why you need the tool to fit the new filter.


__________________________________________________
1992 K100LT 0193214 Bertha Blue 101,000 miles
1984 K100RT 0022575 Brutus Baja Red 578 bought 36,000 now 89,150 miles
1997 K1100LT 0188024 Wotan Mystic Red 689 58,645 now 106,950 miles Deceased.
1983 K100RS 0011157 Fricka 606 Alaska Blue 29,495 miles Damn K Pox Its a Bat outta Hell Now 58,200 miles. 
1996 K1100LT 0233004 Lohengrin Mystic Red 38,000 miles currently 51,800 miles.
1983 K100RS 0004449 Odette R100 colours 58,000 miles. Sprint fairing now 63,390 miles

Past:
1968 Yamaha 80 YG1
1971 Yamaha 125 YAS-1
1968 Honda 125 SS
1970 Honda CD 175
1973 Honda CB500-4
Honda CX 500
    

7Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Fri Apr 29, 2016 6:19 pm

Holister

Holister
Life time member
Life time member
Danish, the tool is pretty easy to come by. Just ask in your local automotive store or auto trade supplier for a cup type filter wrench. You can buy them online very cheap. Be aware tho that they come in different sizes. Find a filter like a Ryco Z418 or similar, that you can easily get hold of every time, and buy a filter wrench to suit.
You can even buy an adjustable oil filter wrench like this.

As Olaf says, its a good idea to prefill the filter not only for the pump's sake but also for the engine. After an oil change there is very little oil 'up top' and if there's no oil in the filter then it will run cold for a second or two without oil. This is when damage will occur.

When installing the filter, smear oil on the filter seal and do it up finger tight then wrench it just half a turn.... no more.


__________________________________________________

1989 K100RT     VIN  0097367 (naked)  
1996 K1100RS   VIN  0451808
 K100 Oil Filter Change Austra12    Fuel:  95 Octane
Engine Oil: Nulon Full Synthetic 15W50
Gear Box Oil:  Nulon Synthetic 75W90
    

8Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Fri Apr 29, 2016 7:06 pm

Inge K.

Inge K.
VIP
VIP
The original tool from BMW is Hazet 2169.


__________________________________________________
Inge K.
K100RS -86. (first owner), K1100LTSE -94.
    

9Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Sat Apr 30, 2016 3:46 am

Danish biker

Danish biker
Platinum member
Platinum member
Thanks. Holister I like the adjustable tool Very Happy How ever I'll go by the local bike shop and borrow the tool (for free Very Happy).

    

10Back to top Go down   K100 Oil Filter Change Empty Oil filter tool Sat Apr 30, 2016 11:26 am

kdiv2011

kdiv2011
active member
active member
http://www.euromotoelectrics.com/BMW-Oil-Filter-Wrench-Tool-BMW-R-and-K-p/of-wrench14f448.htm

It doesn't answer your question about it being stuck now, but if you were looking for one here's a place to get one over on this corner. It doesn't appear too pricey and they ship worldwide.

Good luck.
Cheer.


__________________________________________________
www.bmwarchive.org/vin/bmw-vin-decoder.html says
Data for vehicle identification number: WB1050607L0178661
Model: K100LT |Market: Europa | Type: 0506 | E-Code: K589
Engine: 4-ZYL - 1,00l (66kW) | Body Color: Rot Metallic (654)
Production date: 17.01.1990
    

11Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Sat Apr 30, 2016 1:39 pm

Danish biker

Danish biker
Platinum member
Platinum member
I bought an adjustable one, just for the fun. Of course it won't fit but I was aware that it might not work so I borrowed the one from the bike shop and it worked great.

Tanks for your answers Very Happy


K100 Oil Filter Change Image_zps7p5sfshj


__________________________________________________
You have enemies? Good. That means you've stood up for something, sometime in your life.
-Sir Winston Churchill
    

12Back to top Go down   K100 Oil Filter Change Empty Not to hard to find.. Tue Aug 23, 2016 3:58 pm

Bumblebee

Bumblebee
Silver member
Silver member
You can use a cup type oil filter wrench, these are available in a number of sizes from your local auto parts store.  Take a new filter with you to find one that will fit.

As for pre-filling the filter with oil, not absolutely necessary, but a good idea.  If the filter is not full after it's been changed the engine will run for a few seconds (maybe 5 to 7) with no oil pressure.  In the service manual BMW suggests pre-filling the filter when it's installed, this is what I do and the oil pressure comes right up after the engine is started after and oil and filter change.

- B

http://Bugsmashers.org/phpbb
    

13Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Thu Sep 01, 2016 10:36 am

halflive

halflive
Silver member
Silver member
I use a piece of PVC sewer pipe. I do not know the exact diameter, but the outher diameter is about the same as the filter. i cut a piece of about 12cm and heated one side with a heat blower gun. You push it over the wrench side of a new filter and let it cool. Once cooled you have a perfect and cheap filter wrench.

http://halflive.hostei.com
    

14Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Thu Sep 01, 2016 11:22 am

duck

duck
Life time member
Life time member
Crazy Frog wrote:Hey Mike

The reason that I fill up the filter is that I don't like to have my oil pump running dry (even for few seconds). The other reason is that when the filter is pre-filled, when filling up the engine you just have to look at the site glass. Usually, If I fill it up to 3/4 of the site glass I don't have to add any oil after. I never rely on the book for oil quantity. The site glass is what count.

A filter wrench is cheap here in Cdn. I may be able to send you one. Just contact me by Email.

Cheers

Bert

Unless you're waiting a long, long time between draining and refilling, your oil pump is never running dry. There's plenty of residual oil left on the parts even after you've drained it.


__________________________________________________
Current stable:
86 Custom K100 (standard fairing, K75 Belly pan, Ceramic chromed engine covers, paralever)
K75 Frankenbrick (Paralever, K11 front end, hybrid ABS, K1100RS fairing, radial tires)
86 K75C Turbo w/ paralever
94 K1100RS
93 K1100LT
91 K1
93 K75S (K11 front end)
91 K75S (K1 front end)
14 Yamaha WR250R
98 Taxi Cab K1200RS
14 K1600GT
http://www.ClassicKBikes.com
    

15Back to top Go down   K100 Oil Filter Change Empty oil filter option Thu Sep 01, 2016 11:30 am

nvboy

nvboy
Silver member
Silver member
Am I the only one that uses filters that have a nut attached to the bottom (top?) of the filter?  I've never had an issue with them and any tool kit will have a wrench that will fit the nut.  No need to purchase/carry a special tool.

https://www.amazon.com/KN-163-BMW-High-Performance-Filter/dp/B000E28CBS/ref=sr_1_3?ie=UTF8&qid=1472739826&sr=8-3&keywords=oil+filter+for+1989+bmw+k100

Darrin


__________________________________________________
K100 Oil Filter Change Can-lo10
    

16Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Thu Sep 01, 2016 12:00 pm

Two Wheels Better

Two Wheels Better
Moderator
Moderator
Realising that this is an older thread...it's fun to see how common issues reoccur over time. I just changed the oil on a K100 in my garage. As I was unscrewing the three bolt cover to allow the oil to drain away from the filter cavity, I saw what apeared to be an aftermarket oil filter case in black. In fact it was the inexpensive black oil filter tool that the  last person in there had left attached to the oil filter. No harm done, plenty of room and no paint came off it and ran through the engine, but I could imagine him wandering about the garage later, scratching his head, saying, "Now where did my filter tool get to!?

The last two (a K&N and an off brand) oil filters I have removed from bikes I've worked on have stripped the tacked on 'nut' right off with the lightest of mechanical force. I'm sure the guts of K&N filters are acceptable, having cut one of them open to view the filtration media and pressure relief valve's construction, but the method of removal leaves a lot to be desired. The worst part is the hot, used oil dripping all over the place after having to puncture the can to twist it off. How much in the manufacturing process are they really saving by not impressing wrench 'flutes' into the filter case but leaving them smooth and round?! I am not a fan.

When you purchase Motobins' oil filters a tool is supplied with each filter, last time I bought eight in an order. In the US, Tucker Rocky sell a $9.00 filter tool made of stamped steel that fits BMW OEM (11421460845, 11427721779, 11427719857 & etc) oil filters without the price of the BMW Hazet tool. You can purchase one of those from any motorbike shop.


__________________________________________________
"A long ride is the answer to a question you will soon forget!" ~ Anonymous
1977 R75/7-100, '93 K11/K12 Big Block, '93 K1100RS, '95 R100 Mystic, '96 K1100RS, 2 x '98 K1200RS, '06 K1200R & '09 K1300GT
    

17Back to top Go down   K100 Oil Filter Change Empty oil change, now heat shield Wed Mar 15, 2017 12:44 pm

Stumiester

Stumiester
active member
active member
Two Wheels Better wrote:Realising that this is an older thread..
Older thread but new audience. at least in my case.
So I am in the middle of going through my 87 K100RS having not yet driven it. We just got 20" of snow so it will be a while.  Oil change and dropping the oil pan to see what the PO did or did not do.  There was a persistent leak from the cold bike, a couple drops every day, surely the warm bike will leak much more.  taking the lower fairing off it was gooey with oil. So I am reading about where the leaks often come from, not he main, the oil pan edge does not appear to be leaking but the round cover does.  Not much crud in the main pan (good), the o-ring was well sealed with excess rtv. But still leaked.  so I examine the mating surface on the oil pan where the round cover goes, the aluminum surface which is smooth everywhere else looks like it has ripples, and irregularities. kinda like when you try to spread cold butter on your toast.  not gouges but maybe cut marks  probably from an errant razor blade scraper. I thought about sanding it smooth but also thought a machinist would be able to resurface it. Then the cost factor came to mind and I realize a replacement oil pan is going to be cheaper than a half hour at a machine shop. hope the new pan solves the problem, since I have identified it I am sure it will.  next question is on the heat shield which attaches to the (passenger side?) right side of the oil pan with pins and grommets?  I can't see a good picture so I assume this is what is standard.  The left side has some nice rubber bumpers with mounted studs, but these pins look very different.

    

18Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Wed Mar 15, 2017 1:16 pm

92KK 84WW Olaf

avatar
Life time member
Life time member
I think those items you mention on the left side of the oil pan relate to mountings for the belly pan or engine bars. They are also on my LT which was a police bike and presumably had the bars on it before it came to me.

The cuts and gouges may have been caused by a previous owner trying to remove the oil filter without having the tool or without dropping the oil pan.


__________________________________________________
1992 K100LT 0193214 Bertha Blue 101,000 miles
1984 K100RT 0022575 Brutus Baja Red 578 bought 36,000 now 89,150 miles
1997 K1100LT 0188024 Wotan Mystic Red 689 58,645 now 106,950 miles Deceased.
1983 K100RS 0011157 Fricka 606 Alaska Blue 29,495 miles Damn K Pox Its a Bat outta Hell Now 58,200 miles. 
1996 K1100LT 0233004 Lohengrin Mystic Red 38,000 miles currently 51,800 miles.
1983 K100RS 0004449 Odette R100 colours 58,000 miles. Sprint fairing now 63,390 miles

Past:
1968 Yamaha 80 YG1
1971 Yamaha 125 YAS-1
1968 Honda 125 SS
1970 Honda CD 175
1973 Honda CB500-4
Honda CX 500
    

19Back to top Go down   K100 Oil Filter Change Empty Re: K100 Oil Filter Change Wed Mar 15, 2017 3:38 pm

Stumiester

Stumiester
active member
active member
yes, my bike had crash bars at one time, no longer present. so that could explain some things. 
the oil filter removal without the proper tool makes sense.  I can now picture one of those serrated tooth filter wrenches, some skinned knuckles and some swearing.

    

Sponsored content


    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum