BMW K bikes (Bricks)


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


dark_gap

dark_gap
active member
active member
Good afternoon, I have a problem with the turn signals and horn of my bike, the buttons are really stiff and to turn on any of the turn signals, to stop it or to press the horn are really painful so...trying to repair this mess I have remove all the screws of the left handlebar switch, I have download the wiring diagrams from this helpful forum...but I discover that the little metallic 'dots' inside the high beam switch are really rusty, while I was cleaning it with some zero residue spray and low grit sandpaper, one of the cables has unsoldered and don't know where it goes...

So...can anybody post some photos of the inside of the switches to view which cable goes where...if you can upload of the both handlebar switches it will be very helpful cause tonight I will do the same with the righ side and I fear that the stuff will be the same...

Thanks a lot!!

    

Holister

Holister
Life time member
Life time member
This will have the info you need
Reparing Left Switch Block - Gaz80


__________________________________________________

1989 K100RT     VIN  0097367 (naked)  
1996 K1100RS   VIN  0451808
 BMW K1/K100RS - Left Handlebar Switch Diagram/photo? Austra12    Fuel:  95 Octane
Engine Oil: Nulon Full Synthetic 15W50
Gear Box Oil:  Nulon Synthetic 75W90
    

dark_gap

dark_gap
active member
active member
Kaptain Holister wrote:This will have the info you need
Reparing Left Switch Block - Gaz80


Wow! Thanks a lot, I promise I have spend about 20 minutes searching, but as far as I'm searching maybe the wrong words, this post did't appear.

Thanks a lot! I will try tomorrow to find where the cable was unsoldered.

    

indian036

indian036
Life time member
Life time member
Hi dark_gap,

KH has made the thread name a hyperlink, so you can just click on the line Reparing Left Switch Block - Gaz80  in his original post or your quote of his post, or this post.

(The search problem may also be that KH misspelled 'repairing' in this post.)  Wink   Link still works, though.

Bill


__________________________________________________
1985 K100RT  VIN 0028991  My original Very Happy ROB the Red Old Bike   (Historic rego)
1985 K100RT  VIN 0029036  BOB the Blue Old Bike  (Historic rego)
1990 K100LT  VIN 0190452  Work in progress
1984 K100RT  VIN 0023022  Work needing lots of progress

1986 K100RT  VIN 0090542  Work needing lots and lots of progress
1993 K1100LT  VIN 0183046  Work in progress
1993 K75S  VIN 0213045  Tom the Triple (now on Historic rego too.)
    

dark_gap

dark_gap
active member
active member
indian036 wrote:Hi dark_gap,

KH has made the thread name a hyperlink, so you can just click on the line Reparing Left Switch Block - Gaz80  in his original post or your quote of his post, or this post.

(The search problem may also be that KH misspelled 'repairing' in this post.)  Wink   Link still works, though.

Bill

Thanks Bill, yes it works anyway. I found that there was a unsoldered cable that I have repair...but turn lights still flashing when they want after pressing the right or left button...I think that I must check all the wiring and also the flashing lights relay, well maybe all hehehe

I will keep you updated!

Thanks Again!

Cheers!

    

Sponsored content


    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum