BMW K bikes (Bricks)


You are not connected. Please login or register

View previous topic View next topic Go down  Message [Page 1 of 1]


svlwolf

svlwolf
active member
active member
OK, I changed tires to shinko 244 series front and back, as I understand these tires can be used for either front or back, i assume that means that there is no rotation arrows on these tires whatsoever, anyway i noticed last night that the right side brake disc was against the fork, i took the allen bolt out of the axle and it moved out away from fork, Now mind you I just put the front tire on and had to DRIVE the axle in, SOOOO this morning I starting DRIVING the axle out with a socket and behold I notice on the right side the bearing has come out and stuck on the axle, anyway got that off and the spacers etc and straightened the lips of the spacer cups , i have taken 600 grit wet dry sandpaper to the end of the axle as i saw some nicks on it and smoothed it up, i cannot get the axle thru the bearings at all, matter of fact i would have to drive the axle in to get them on, i know its close tolerance but damn not that much..

So I am assuming something was not lined up when i installed and frigged the bearings on both sides, have both of them out and about to go get 2 new ones, any thoughts on this? cheers Do the spacer cups and end of axle look ok to you guys????


DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 20150511

DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 20150512
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 20150513
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 20150514
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 20150515
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 20150516
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 20150517

    

Born Again Eccentric

Born Again Eccentric
Life time member
Life time member
Svlwof - sounds like you are having something of a saga.

Most tyres have a direction of rotation on them - even if they can be used for front or rear. If you have ABS brakes, getting the wheel back on the right way round is easy - the toothed ABS sensor wheel is on the right hand side (just need to make sure the tyre is mounted correctly for the correct rotation)


DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Img_7614

With the wheel correctly installed, you will have a 3-4mm gap between the brake discs and the forks on both sides. Are you sure that you have put the spacers back correctly? 

The axle is removed by slackening the two clamp bolts on the forks (two on each fork) and removing the allen screw from the left hand end of the axle spindle (I assume that you slackened these off). The axle should then slide out smoothly to the right hand side (if it wasn't lightly greased when installed, it can be quite stiff to move) using a tommy bar or some such passed through the hole at the right hand end of the axle spindle to allow the axle to be pulled out with a twistlng motion. 

With the axle removed, two spacers will drop free - the larger of the two must be re-installed on the left side of the wheel and the smaller on the right. The wheel bearings are a press fit in the wheel hub and should not come out at all.


DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Img_7616  DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Img_7615
Right hand side (thin spacer)                                                     Left hand side (fat spacer)

The difficulty you are having getting the axle spindle out or in again suggests that you may have bent the spindle or maybe that your forks are not correctly aligned. It should not be that tight a fit.

Have you tried putting the axle spindle thought the wheel hub with it off the bike? (i.e. not going through the forks). This would give an idea if the spindle is bent or not. If it slides though easily, then I would look at your fork alignment. If it doesn't, then that suggests damage to the spindle.

Ordinarily, getting the wheel back on is pretty easy. Get wheel between forks and brake callipers positioned on the brake discs. The axle spindle slides in from the right hand side, through the right fork, through the thin spacer, through the wheel hub, through the fat spacer and through the left hand fork and is then secured with the allen screw (to the correct torque). Pump the forks a few time to align the forks and then tighten the clamp bolts to the correct torque. It is usually to have to lift the wheel slightly to get the spindle through the fat spacer and left fork.

Good luck!


__________________________________________________
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Uk-log10 DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Sco-lo15
                              Paul  DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 905546712

"Heidi" K100LT 1991 (Grey) (VIN 0190172 Engine No. 104EB 2590 2213) - 5th owner. January 2014 (34,000 - 82,818 miles and counting....)
"Gretel" K100LT 1989 (Silver Grey) (VIN 0177324 Engine No. 104EA 2789 2211) - 4th+ owner. September 2015 (82,684 miles and counting....). Cat C Insurance write-off rebuild Feb 17
"Donor" K100LT 1990 (Red)  (VIN 0178091 Engine gone to Dai) - 6th & final owner (crash write-off now donor bike).   June 2012 (73,000 miles) to November 2013 (89,500 miles)
    

svlwolf

svlwolf
active member
active member
Born Again Eccentric wrote:Svlwof - sounds like you are having something of a saga.

Most tyres have a direction of rotation on them - even if they can be used for front or rear. If you have ABS brakes, getting the wheel back on the right way round is easy - the toothed ABS sensor wheel is on the right hand side (just need to make sure the tyre is mounted correctly for the correct rotation) Svlwolf here, nowhere on these tires is an arrow like the original tires, they are knobby tires, i am absless, just good ole disc


DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Img_7614

With the wheel correctly installed, you will have a 3-4mm gap between the brake discs and the forks on both sides. Are you sure that you have put the spacers back correctly? Wolf here, yes I put the spacers on the right sides, BUT a possiblilty

The axle is removed by slackening the two clamp bolts on the forks (two on each fork) and removing the allen screw from the left hand end of the axle spindle (I assume that you slackened these off). The axle should then slide out smoothly to the right hand side (if it wasn't lightly greased when installed, it can be quite stiff to move) using a tommy bar or some such passed through the hole at the right hand end of the axle spindle to allow the axle to be pulled out with a twistlng motion. Svlwolf here, yes no problems originally when i removed it to replace the tires

With the axle removed, two spacers will drop free - the larger of the two must be re-installed on the left side of the wheel and the smaller on the right. The wheel bearings are a press fit in the wheel hub and should not come out at all. Svlwolf here, yes large on left and small on right , yes i know they should be press fit


DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Img_7616  DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Img_7615
Right hand side (thin spacer)                                                     Left hand side (fat spacer)

The difficulty you are having getting the axle spindle out or in again suggests that you may have bent the spindle or maybe that your forks are not correctly aligned. It should not be that tight a fit. Svlwolf here, yes i did notice that the fork on the right side was sitting a little lower than the left side, so possible fork alignment the first time

Have you tried putting the axle spindle thought the wheel hub with it off the bike? (i.e. not going through the forks). This would give an idea if the spindle is bent or not. If it slides though easily, then I would look at your fork alignment. If it doesn't, then that suggests damage to the spindle. Svlwolf here, doesnt slide through either bearing at all, alll the other spacers etc go on just fine

Ordinarily, getting the wheel back on is pretty easy. Get wheel between forks and brake callipers positioned on the brake discs. The axle spindle slides in from the right hand side, through the right fork, through the thin spacer, through the wheel hub, through the fat spacer and through the left hand fork and is then secured with the allen screw (to the correct torque). Pump the forks a few time to align the forks and then tighten the clamp bolts to the correct torque. It is usually to have to lift the wheel slightly to get the spindle through the fat spacer and left fork.

Good luck!

    

Born Again Eccentric

Born Again Eccentric
Life time member
Life time member
Sorry - not trying to tell you the obvious, just trying to work out what's gone wrong.

The tyre rotation thing is a bit of a red herring (does that translate globally?) - there is no way that simply fitting the right sizes tyres could affect the axle spindle - even if they were put on with the rotation in the wrong direction (that just affects road handling performance). If you have gone for knobbly tyres - then it is quite likely that it really doesn't matter which way they go on as the tread is pretty uniform.

Bit concerned by your statements:

"Svlwolf here, yes no problems originally when i removed it to replace the tires"
and
"I just put the front tire on and had to DRIVE the axle in, SOOOO this morning I starting DRIVING the axle out with a socket

This sounds like you have had some misalignment, but have forced the spindle in, causing it to bind with the wheel bearing - probably damaging both the bearings and the spindle. Bugger! You may need new bearings (not expensive, but not a simple job to fit (BMW talks of heating up the wheel to get the new bearings in - tyre off job!!)) and maybe a new spindle too.


__________________________________________________
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Uk-log10 DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Sco-lo15
                              Paul  DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 905546712

"Heidi" K100LT 1991 (Grey) (VIN 0190172 Engine No. 104EB 2590 2213) - 5th owner. January 2014 (34,000 - 82,818 miles and counting....)
"Gretel" K100LT 1989 (Silver Grey) (VIN 0177324 Engine No. 104EA 2789 2211) - 4th+ owner. September 2015 (82,684 miles and counting....). Cat C Insurance write-off rebuild Feb 17
"Donor" K100LT 1990 (Red)  (VIN 0178091 Engine gone to Dai) - 6th & final owner (crash write-off now donor bike).   June 2012 (73,000 miles) to November 2013 (89,500 miles)
    

svlwolf

svlwolf
active member
active member
Born Again Eccentric wrote:Sorry - not trying to tell you the obvious, just trying to work out what's gone wrong.

Wolf here, No worry at all about the obvious, just trying to work thru it myself

The tyre rotation thing is a bit of a red herring (does that translate globally?) - there is no way that simply fitting the right sizes tyres could affect the axle spindle - even if they were put on with the rotation in the wrong direction (that just affects road handling performance). If you have gone for knobbly tyres - then it is quite likely that it really doesn't matter which way they go on as the tread is pretty uniform. Wolf here, my thoughts exactly!

Bit concerned by your statements:

"Svlwolf here, yes no problems originally when i removed it to replace the tires"
and
"I just put the front tire on and had to DRIVE the axle in, SOOOO this morning I starting DRIVING the axle out with a socket

This sounds like you have had some misalignment, but have forced the spindle in, causing it to bind with the wheel bearing - probably damaging both the bearings and the spindle. Bugger! You may need new bearings (not expensive, but not a simple job to fit (BMW talks of heating up the wheel to get the new bearings in - tyre off job!!)) and maybe a new spindle too. Svlwolf here, I just put the spindle on a straight edge at different locations all the way around the spindle, no signs at all of being warped or bent, however my thinking is about the bearings and am about to go get 2 to see if i may fix the problem!!

Trust me your input is very much appreciated  cheers



    

Inge K.

Inge K.
VIP
VIP
Be aware that it is a distance tube between the two bearings, it can have been malformed as it is rather soft.

DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Distan10


__________________________________________________
Inge K.
K100RS -86. (first owner), K1100LTSE -94.
    

svlwolf

svlwolf
active member
active member
Yep the only thing i can see was one of the little "caps" on the end of the distance tube was a little bent, so i had read on here somewhere just to straighten it, and BTW just took the axel up to a guy at an auto parts house that works on bikes as well and he confirmed he saw nothing about the axle that would be the issue.. And looking up the fag and skf#'s didnt help him with Oreilly's , anyone have an alternate bearing that is available through auto parts houses in the USA?

    

Inge K.

Inge K.
VIP
VIP
That is standard bearings  SKF 6005 2RSH. (47 x 25 x 12 mm).


__________________________________________________
Inge K.
K100RS -86. (first owner), K1100LTSE -94.
    

svlwolf

svlwolf
active member
active member
Ok, took some medium grit sand paper and worked the end of the axel and then 3M cloth and polished, bearings slide on and off with just enough resistance now!!!! gonna install and remount,,, carefully!!!!

    

Born Again Eccentric

Born Again Eccentric
Life time member
Life time member
That sounds like good news. The spindle is necessarily a very close fit in the bearings and it wouldn't take much distortion (caused by "driving out", possibly) to prevent it fitting at all. Glad to hear you were able to dress out the end of the spindle and get it to fit again.

Hope the rebuild goes smoothly.


__________________________________________________
DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Uk-log10 DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Sco-lo15
                              Paul  DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 905546712

"Heidi" K100LT 1991 (Grey) (VIN 0190172 Engine No. 104EB 2590 2213) - 5th owner. January 2014 (34,000 - 82,818 miles and counting....)
"Gretel" K100LT 1989 (Silver Grey) (VIN 0177324 Engine No. 104EA 2789 2211) - 4th+ owner. September 2015 (82,684 miles and counting....). Cat C Insurance write-off rebuild Feb 17
"Donor" K100LT 1990 (Red)  (VIN 0178091 Engine gone to Dai) - 6th & final owner (crash write-off now donor bike).   June 2012 (73,000 miles) to November 2013 (89,500 miles)
    

svlwolf

svlwolf
active member
active member
WOW!!! WHAT A DAY

OK, bearings back in with distance tube between them, everything all lined up , shaft slides in and bumped through with palm of hand cheers, then on to put the allen bolt in the end of the axle, NNOOOOOOOO threads are buggered up right at end

SOOOOO find M10 tap, finally get threads cut into good threads , put washer on, screw Allen bolt in and torqued to spec,  santa brake calipers back on, fork pinch bolts in , tire spins like a merry go round

I have had a learning and fulfilling experience today! Really it sucked but I overcame :king:

    

Stan

Stan
Life time member
Life time member
It is all a learning experience. Beware of the  "safe place". If you ever put anything in this spot when stripping an item......you will not find it....for a very long time.



Last edited by ainsjac on Mon May 18, 2015 4:10 am; edited 1 time in total


__________________________________________________
1983 K100 basic vin 0003960 colour red  GONE
1987 K100RT vin 0094685 colour, orange peel, sorry, pearl..GONE
F800R black
    

svlwolf

svlwolf
active member
active member
Oh yes it is very much a learning experience as I have never, ever worked on anything remotely close to a motorcycle Evil or Very Mad

There are no safe places DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 259495


__________________________________________________
1985 K100RS amidst customization bounce


DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Usa-lo10
    

Holister

Holister
Life time member
Life time member
Aaahhh yes! the safe palce. Laughing  You scour the garage looking for that 10mm socket you just put down where you new you'd be able to get to it quickly while you're swapping out tools..... nope. Not there. You go upstairs thinking you left it on the kitchen bench when you made a cuppa. nope... not there. You check to see if its beer'o'clock yet but decide to make another cuppa Very Happy . You check your pockets again just in case you're going crazy. Nope. Back down stairs to have another look then scrounge thru a box of old sockets to find one that could fit. Back to the job and there it is sitting on the front of the bench where you left it. A few swear words at myself... DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 161205 .... now, what was I doing? Laughing


__________________________________________________

1989 K100RT     VIN  0097367 (naked)  
1996 K1100RS   VIN  0451808
 DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Austra12    Fuel:  95 Octane
Engine Oil: Nulon Full Synthetic 15W50
Gear Box Oil:  Nulon Synthetic 75W90
    

Stan

Stan
Life time member
Life time member
Yes...safe places can also be expensive...I have many duplicate sets of nuts and bolts as a result of the "safe place".


__________________________________________________
1983 K100 basic vin 0003960 colour red  GONE
1987 K100RT vin 0094685 colour, orange peel, sorry, pearl..GONE
F800R black
    

indian036

indian036
Life time member
Life time member
Kaptain Holister wrote:Aaahhh yes! the safe palce. Laughing  You scour the garage looking for that 10mm socket you just put down where you new you'd be able to get to it quickly while you're swapping out tools..... nope. Not there. You go upstairs thinking you left it on the kitchen bench when you made a cuppa. nope... not there. You check to see if its beer'o'clock yet but decide to make another cuppa Very Happy . You check your pockets again just in case you're going crazy. Nope. Back down stairs to have another look then scrounge thru a box of old sockets to find one that could fit. Back to the job and there it is sitting on the front of the bench where you left it. A few swear words at myself... DAMNIT ALWAYS SOMETHING!!!!!Little Help needed 161205 .... now, what was I doing? Laughing
Not a problem when you have at least 6 socket sets of varying size range and quality, and all of them cover 10mm.   Very Happy

Bill


__________________________________________________
1985 K100RT  VIN 0028991  My original Very Happy ROB the Red Old Bike   (Historic rego)
1985 K100RT  VIN 0029036  BOB the Blue Old Bike  (Historic rego)
1990 K100LT  VIN 0190452  Work in progress
1984 K100RT  VIN 0023022  Work needing lots of progress

1986 K100RT  VIN 0090542  Work needing lots and lots of progress
1993 K1100LT  VIN 0183046  Work in progress
1993 K75S  VIN 0213045  Tom the Triple (now on Historic rego too.)
    

Point-Seven-five

Point-Seven-five
Life time member
Life time member
You can never have too many 10, 12, 13, and 14mm wrenches...


__________________________________________________
Present: 1991 K100RS "Moby Brick Too"
 
Past:
1994 K75RT "Ilsa, She Wolf of the SS"
1988 K100RS SE "Special Ed"
1994 K75S "Cheetos"
1992 K100RS "Moby Brick" R.I.P.
1982 Honda FT500
1979 Honda XR185
1977 Honda XL125
1974 Honda XL125
1972 OSSA Pioneer 250
1968 Kawasaki 175
    

svlwolf

svlwolf
active member
active member
I also have an 88 Isuzu Trooper soooo YES I have Metric tools hid in places like some people hide guns to be able to get to anywhere in there home,,, its just my guns have a couple 10mm wrenches beside them!!!


__________________________________________________
1985 K100RS amidst customization bounce


DAMNIT ALWAYS SOMETHING!!!!!Little Help needed Usa-lo10
    

Sponsored content


    

View previous topic View next topic Back to top  Message [Page 1 of 1]

Permissions in this forum:
You cannot reply to topics in this forum